CUSTOM ORDER SPECIFICATIONS

CUSTOM ORDER SPECIFICATIONS

LUIS JORGE


Body 1:

 6 string Ibanez Jem shaped body with hole for hand

-Mahogany wood (please do not use more than 2 pieces if possible)

-painted top like foto on attachement

-Rear routed

-All Access Neck Joint (AANJ)

-routed for humbucker(bridge)+single-coil (in the neck)

-routed for floyd rose tremolo with lion's claw 

-with forearm bend countour, and belly contour

-Clear (uncolored) heavier polyester glossy finish, so that you can see mahogany wood on back of body

-body should be all completed ready for assembly all parts



_______________________________ DONE:_______________________________ 

Neck 1:

 -6 string neck with reversed Ibanez headstock (like foto on atachement)

-3 piece maple with angled headstock

-birdseye maple fingerboard

-disapearing pyramid inlays, in green+yelow+ pink color (like foto) in printed graphic under a clear acrylc with bright/vibrant colors

-All Access Neck Joint (AANJ)

-Dunlop 6000 fretwire

-24 frets

-25,5" scale lenght

-19mm thickness at 1st fret (wiazard II-USA back profile)

-i'd like to put a Gotoh Floyd Rose, and i'm not shure what is the apropriate radius. So what fingerboard radius would you recomend?

-standart side dot inlays

-43mm width at nut

-last 4 fret scalop

-prepared for rearmount locking nut (43mm width)

-do not drill neck screws where atach to body (i'm thinking in doing that myself for better fit)

-glossy clear urethane sprayed (back neck, headstock and fingerboard)

-tuners holes driled (i think standart is 10mm diameter)

-neck should be all completed ready for assemblying all parts


Neck 2:

 -6 string neck with reversed Ibanez headstock (like foto on atachement)

-3 piece maple with angled headstock

-birdseye maple fingerboard

-disapearing pyramid inlays, in green pyramids with eyes  (like foto)

-All Access Neck Joint (AANJ)

-Dunlop 6000 fretwire

-24 frets

-25,5" scale lenght

-19mm thickness at 1st fret (wiazard II-USA back profile)

-i'd like to put a Gotoh Floyd Rose, and i'm not shure what is the apropriate radius. So what fingerboard radius would you recomend?

-standart side dot inlays

-43mm width at nut

-last 4 fret scalop

-prepared for rearmount locking nut (43mm width)

-do not drill neck screws where atach to body (i'm thinking in doing that myself for better fit)

-hand aplied poly (back neck, headstock and fingerboard)

-tuners holes driled (i think standart is 10mm diameter)

-neck should be all completed ready for assemblying all parts

Neck 3:

6 string neck

-3 piece angled maple neck

-Reversed and angled ibanez headstock

-24 fret

-25.5" scale

-Dunlop 6000 fretwire

-ebony fingerboard

-blue GraFX pyramids inlay (like foto on attachement)

-headstock with swirl printing to match the body it will go with it (please see attached foto of the body)

-43mm nut width

-AANJ (all access neck joint)

-Wizard II-USA back neck profile (19mm at 1st fret, and 21 at 12th fret)

-standart truss-rod

-standart side dot inlays

-prepared for rearmount locking nut (43mm width)

-holes already driled for tuners (standart 10mm diameter)

-do not drill neck screws where atach to body (i will do that myself)

-finished back of neck and headstock(front and back) hand aplyed

----------------------------------------------------------------------------------------------------------

200